www.vishay.com 99 type 710p vishay sprague document number: 42034 revision 17-nov-03 for technical questions, contact spresale@vishay .com film/foil capacitors polypropylene, high frequency wrap-and-fill features extended foil construction low loss high average ac current moisture resistant low dissipation performance characteristics operating temperature: - 55 c to + 85 c. capacitance range: 0.001 f to 1.0 f. capacitance tolerance: 20%, 10%, 5%. dc voltage rating: 200 wvdc to 800 wvdc. voltage derating: at + 105 c, 50% of + 85 c rating. dissipation factor: 0.1% maximum. voltage test: 250% of rated voltage for 5 seconds. insulation resistance: at + 25 c: 200,000 megohm - microfarads or 400,000 megohm minimum. at + 85 c: 10,000 megohm - microfarads or 20,000 megohm minimum. at +105 c: 1000 megohm - microfarads or 2000 megohm minimum. pulse capability ( ? v/ ? t): 200 wvdc - 300 v/ sec maximum. 400 wvdc - 400 v/ sec maximum. 600 wvdc - 500 v/ sec maximum. 800 wvdc - 600 v/ sec maximum. environmental characteristics vibration test (condition b): no mechanical damage, short, open or intermittent circuits. dc life test: 150% of rated voltage for 500 hours @ + 85 c. no open or short circuits. no visible damage. maximum ? cap: 5%. minimum i.r. = 50% of initial limit. maximum d.f. = 0.1%. humidity test: 95% relative humidity @ + 75 c for 72 hours. no visible damage. minimum i.r. = 25%. ac life test: 110% of rated rms voltage for 500 hours. see ac voltage ratings for voltage, frequency and temperature. maximum ? cap: 5%. minimum i.r. = 50% of initial limit. maximum d.f. = 0.1%. physical characteristics lead pull: 5 pounds (2.3 kilograms) for one minute. no physical damage. lead bend: after three complete consecutive bends, no damage. marking: sprague ? trademark, type or part number, capacitance and voltage. * leads to be within 0.062" [1.57mm] of center line at egress but not less than 0.031" [0.78mm] from edge. ac voltage ratings equivalent vac ratings @ 10,000hz 5000hz 1000hz 20,000hz wvdc 200 v 400 v 600 v 800 v + 85 c 155 155 155 200 200 200 200 200 200 500 500 500 + 105 c 75 75 75 100 100 100 140 140 100 250 250 195 + 85 c 115 75 75 190 100 100 200 125 125 500 400 280 + 105 c 75 60 50 100 80 50 165 95 55 190 120 75 + 85 c 85 55 55 135 75 75 160 90 90 500 240 160 + 105 c 60 40 30 105 55 30 120 65 30 150 100 45 + 85 c 70 45 45 110 60 60 130 75 75 450 185 115 + 105 c 50 35 20 85 45 20 100 55 20 120 75 30 + 85 c 60 40 40 95 50 50 110 65 60 405 140 85 + 105 c 45 30 15 75 40 15 85 45 15 100 60 20 maximum ac life test voltage (rms) 155 155 155 200 200 200 200 200 200 500 500 500 capacitance range ( f) 0.012 - 0.068 0.082 - 0.47 0.68 - 1.0 0.0039 - 0.033 0.039 - 0.47 0.68 - 1.0 0.001 - 0.033 0.039 - 0.22 0.27 - 1.0 0.0056 - 0.033 0.039 - 0.10 0.12 - 0.56 15,000hz dimensions in inches [millimeters] d max. 1.750 [44.45] min. solid tinned leads* 0.032 [0.81] nominal diameter (no. 20 awg) 1.750 [44.45] min. l + 0.062 [1.57]
document number: 42034 revision 17-nov-03 www.vishay.com 100 type 710p vishay sprague for technical questions, contact spresale@vishay .com standard ratings in inches [millimeters] 200 wvdc nominal case size 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.01 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.68 0.82 1.00 710p123x9200 710p153x9200 710p183x9200 710p223x9200** 710p273x9200 710p333x9200 710p393x9200 710p473x9200** 710p563x9200 710p683x9200 710p823x9200 710p104x9200** 710p124x9200 710p154x9200 710p184x9200 710p224x9200** 710p274x9200 710p334x9200 710p394x9200 710p474x9200** 710p684x9200 710p824x9200 710p105x9200** .750 [19.05] .750 [19.05] .750 [19.05] .750 [19.05] .750 [19.05] .750 [19.05] .938 [23.83] .938 [23.83] .938 [23.83] .938 [23.83] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 2.063 [52.41] 2.063 [52.41] 0.250 [6.35] 0.250 [6.35] 0.290 [7.37] 0.290 [7.37] 0.335 [8.51] 0.335 [8.51] 0.315 [8.00] 0.315 [8.00] 0.375 [9.53] 0.375 [9.53] 0.360 [9.14] 0.360 [9.14] 0.420 [10.67] 0.420 [10.67] 0.495 [12.57] 0.495 [12.57] 0.510 [12.95] 0.510 [12.95] 0.590 [14.99] 0.590 [14.99] 0.799 [20.29] 0.821 [20.85] 0.821 [20.85] l d part number* 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.68 0.82 1.00 600 wvdc 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 * the part numbers listed are for capacitance tolerance of 10%. to specify 20% tolerance, change "x9" in the part number to "x0". for 5% tolerance: change the "x9" to "x5". ** inventoried. 710p392x9400 710p472x9400 710p562x9400 710p682x9400 710p822x9400 710p103x9400** 710p123x9400 710p153x9400 710p183x9400 710p223x9400** 710p273x9400 710p333x9400 710p393x9400 710p473x9400** 710p563x9400 710p683x9400 710p823x9400 710p104x9400** 710p124x9400 710p154x9400 710p184x9400 710p224x9400** 710p274x9400 710p334x9400 710p394x9400 710p474x9400** 710p684x9400 710p824x9400 710p105x9400** 0.240 [6.10] 0.240 [6.10] 0.270 [6.86] 0.270 [6.86] 0.290 [7.37] 0.290 [7.37] 0.330 [8.38] 0.330 [8.38] 0.325 [8.26] 0.325 [8.26] 0.375 [9.53] 0.375 [9.53] 0.355 [9.02] 0.355 [9.02] 0.415 [10.54] 0.415 [10.54] 0.485 [12.32] 0.485 [12.32] 0.570 [14.48] 0.570 [14.48] 0.595 [15.11] 0.595 [15.11] 0.690 [17.53] 0.690 [17.53] 0.830 [21.08] 0.830 [21.08] 0.911 [23.14] 1.091 [27.71] 1.091 [27.71] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.938 [28.83] 0.938 [28.83] 0.938 [28.83] 0.938 [28.83] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 2.438 [61.93] 2.438 [61.93] 2.438 [61.93] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.938 [23.83] 0.938 [23.83] 0.938 [23.83] 0.290 [7.37] 0.305 [7.75] 0.305 [7.75] 0.315 [8.00] 0.315 [8.00] 0.320 [8.13] 0.320 [8.13] 0.330 [8.38] 0.330 [8.38] 0.360 [9.14] 0.360 [9.14] 0.340 [8.64] 0.340 [8.64] 0.390 [9.91] 710p102x9600 710p122x9600 710p152x9600 710p182x9600 710p222x9600 710p272x9600 710p332x9600 710p392x9600 710p472x9600 710p562x9600 710p682x9600 710p822x9600 710p103x9600** 710p123x9600 capacitance ( f) 400 wvdc
www.vishay.com 101 type 710p vishay sprague document number: 42034 revision 17-nov-03 for technical questions, contact spresale@vishay .com 600 wvdc (continued) capacitance ( f) part number d l nominal case size 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 0.33 0.39 0.47 0.56 0.68 0.82 1.00 710p153x9600 710p183x9600 710p223x9600** 710p273x9600 710p333x9600 710p393x9600 710p473x9600** 710p563x9600 710p683x9600 710p823x9600 710p104x9600** 710p124x9600 710p154x9600 710p184x9600 710p224x9600** 710p334x9600 710p394x9600 710p474x9600** 710p564x9600 710p684x9600 710p824x9600 710p105x9600** 0.390 [9.91] 0.450 [11.43] 0.450 [11.43] 0.435 [11.05] 0.435 [11.05] 0.490 [12.45] 0.490 [12.45] 0.590 [14.99] 0.590 [14.99] 0.690 [17.53] 0.690 [17.53] 0.670 [17.02] 0.670 [17.02] 0.800 [20.32] 0.800 [20.32] 0.876 [22.25] 1.032 [26.21] 1.032 [26.21] 1.096 [27.84] 1.096 [27.84] 1.316 [33.43] 1.316 [33.43] 0.938 [23.83] 0.938 [23.83] 0.938 [23.83] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 2.063 [52.41] 2.063 [52.41] 2.063 [52.41] 2.438 [61.93] 2.438 [61.93] 2.438 [61.93] 2.438 [61.93] 800 wvdc 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.275 [6.99] 0.275 [6.99] 0.315 [8.00] 0.315 [8.00] 0.365 [9.27] 0.365 [9.27] 0.430 [10.92] 0.430 [10.92] 0.515 [13.08] 0.515 [13.08] 0.495 [12.57] 0.495 [12.57] 0.595 [15.11] 0.595 [15.11] 0.700 [17.78] 0.700 [17.78] 0.755 [19.18] 0.755 [19.18] 0.910 [23.11] 0.910 [23.11] 0.985 [25.02] 0.985 [25.02] 1.220 [30.99] 1.220 [30.99] 1.220 [30.99] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 1.688 [42.88] 2.063 [52.41] 2.063 [52.41] 2.063 [52.41] 2.063 [52.41] 2.438 [61.93] 2.438 [61.93] 2.438 [61.93] 2.438 [61.93] 2.438 [61.93] 710p562x9800 710p682x9800 710p822x9800 710p103x9800** 710p123x9800 710p153x9800 710p183x9800 710p223x9800** 710p273x9800 710p333x9800 710p393x9800 710p473x9800** 710p563x9800 710p683x9800 710p823x9800 710p104x9800** 710p124x9800 710p154x9800 710p184x9800 710p224x9800** 710p274x9800 710p334x9800 710p394x9800 710p474x9800** 710p564x9800 * the part numbers listed are for capacitance tolerance of 10%. to specify 20% tolerance, change "x9" in the part number to "x0". for 5% tolerance: change the "x9" to "x5". ** inventoried. ordering information x9 capacitance tolerance x0 = 20% x9 = 10% (inventoried) x5 = 5% 200 dc voltage rating this is expressed in volts. 123 capacitance this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. 710p type standard ratings in inches [millimeters]
legal disclaimer notice vishay document number: 91000 www.vishay.com revision: 08-apr-05 1 notice specifications of the products displayed herein are subjec t to change without notice. vishay intertechnology, inc., or anyone on its behalf, assume s no responsibility or liability fo r any errors or inaccuracies. information contained herein is intended to provide a product description only. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in vishay's terms and conditions of sale for such products, vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and /or use of vishay products including liab ility or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyrigh t, or other intellectual property right. the products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify vishay for any damages resulting from such improper use or sale.
|
